Fits blades 100-110 mm.

The kit consists of a pre-marked 3mm Veg tanned leather blank with stitching holes defined and the inside has been prepared to help with the folding of the leather.

A belt loop is also supplied with two rivets that enables the user to decide if left or right-handed use if required.

Some basic instructions:

1. Rivet the belt loop in the desired position.

2. Enlarge the pin pricks with an awl to allow the needles to pass through easily.

3. Soak the sheath in some warm water for about 5 minutes.
This will make the leather very soft and supple.

4. Start sowing from the tip when you reach the top sew back a few stitches to hold it all tight.

5. Wrap your knife in cling film and gently work the knife into the sheath.
Then work with you fingers to mould the leather to take on the shape of your handle.

6. You can leave the leather in it's natural state. It will take on a patina that will darken with time, or
alternatively it can be dyed at this stage, but it's advisable to take the knife out before doing so.
Whatever you decide to do, the knife should only be left in the damp sheath for a couple of hours, then take it out carefully and if you can hang it in a warm place to harden.

These instructions will be included with your kit

More...

Fits blades 90-95mm. Trapper 95 with tapered scales

The kit consists of a pre-marked 3mm Veg tanned leather blank with stitching holes defined and the inside has been prepared to help with the folding of the leather.

A belt loop is also supplied with two rivets that enables the user to decide if left or right-handed use if required.

Some basic instructions:

1. Rivet the belt loop in the desired position.

2. Enlarge the pin pricks with an awl to allow the needles to pass through easily.

3. Soak the sheath in some warm water for about 5 minutes.
This will make the leather very soft and supple.

4. Start sowing from the tip when you reach the top sew back a few stitches to hold it all tight.

5. Wrap your knife in cling film and gently work the knife into the sheath.
Then work with you fingers to mould the leather to take on the shape of your handle.

6. You can leave the leather in it's natural state. It will take on a patina that will darken with time, or
alternatively it can be dyed at this stage, but it's advisable to take the knife out before doing so.
Whatever you decide to do, the knife should only be left in the damp sheath for a couple of hours, then take it out carefully and if you can hang it in a warm place to harden.

These instructions will be included with your kit

More...

Fits blades 110-120mm.x 20mm

The kit consists of a pre-marked 3mm Veg tanned leather blank with stitching holes defined and the inside has been prepared to help with the folding of the leather.

A belt loop is also supplied with two rivets that enables the user to decide if left or right-handed use if required.

Some basic instructions:

1. Rivet the belt loop in the desired position.

2. Enlarge the pin pricks with an awl to allow the needles to pass through easily.

3. Soak the sheath in some warm water for about 5 minutes.
This will make the leather very soft and supple.

4. Start sowing from the tip when you reach the top sew back a few stitches to hold it all tight.

5. Wrap your knife in cling film and gently work the knife into the sheath.
Then work with you fingers to mould the leather to take on the shape of your handle.

6. You can leave the leather in it's natural state. It will take on a patina that will darken with time, or
alternatively it can be dyed at this stage, but it's advisable to take the knife out before doing so.
Whatever you decide to do, the knife should only be left in the damp sheath for a couple of hours, then take it out carefully and if you can hang it in a warm place to harden.

These instructions will be included with your kit

More...

Fits blades 95mm.x 20mm Polar 95

The kit consists of a pre-marked 3mm Veg tanned leather blank with stitching holes defined and the inside has been prepared to help with the folding of the leather.

A belt loop is also supplied with two rivets that enables the user to decide if left or right-handed use if required.

Some basic instructions:

1. Rivet the belt loop in the desired position.

2. Enlarge the pin pricks with an awl to allow the needles to pass through easily.

3. Soak the sheath in some warm water for about 5 minutes.
This will make the leather very soft and supple.

4. Start sowing from the tip when you reach the top sew back a few stitches to hold it all tight.

5. Wrap your knife in cling film and gently work the knife into the sheath.
Then work with you fingers to mould the leather to take on the shape of your handle.

6. You can leave the leather in it's natural state. It will take on a patina that will darken with time, or
alternatively it can be dyed at this stage, but it's advisable to take the knife out before doing so.
Whatever you decide to do, the knife should only be left in the damp sheath for a couple of hours, then take it out carefully and if you can hang it in a warm place to harden.

These instructions will be included with your kit

More...

Fits blades 90mm.x 27mm Bushman

The kit consists of a pre-marked 3mm Veg tanned leather blank with stitching holes defined and the inside has been prepared to help with the folding of the leather.

A belt loop is also supplied with two rivets that enables the user to decide if left or right-handed use if required.

Some basic instructions:

1. Rivet the belt loop in the desired position.

2. Enlarge the pin pricks with an awl to allow the needles to pass through easily.

3. Soak the sheath in some warm water for about 5 minutes.
This will make the leather very soft and supple.

4. Start sowing from the tip when you reach the top sew back a few stitches to hold it all tight.

5. Wrap your knife in cling film and gently work the knife into the sheath.
Then work with you fingers to mould the leather to take on the shape of your handle.

6. You can leave the leather in it's natural state. It will take on a patina that will darken with time, or
alternatively it can be dyed at this stage, but it's advisable to take the knife out before doing so.
Whatever you decide to do, the knife should only be left in the damp sheath for a couple of hours, then take it out carefully and if you can hang it in a warm place to harden.

These instructions will be included with your kit

More...

Fits blades 140mm x 35mm Northern Lights Bushcraft

NOT SHOWN: The kit consists of a pre-marked 3mm Veg tanned leather blank with stitching holes defined and the inside has been prepared to help with the folding of the leather.

A belt loop is also supplied with two rivets that enables the user to decide if left or right-handed use if required.

Some basic instructions:

1. Rivet the belt loop in the desired position.

2. Enlarge the pin pricks with an awl to allow the needles to pass through easily.

3. Soak the sheath in some warm water for about 5 minutes.
This will make the leather very soft and supple.

4. Start sowing from the tip when you reach the top sew back a few stitches to hold it all tight.

5. Wrap your knife in cling film and gently work the knife into the sheath.
Then work with you fingers to mould the leather to take on the shape of your handle.

6. You can leave the leather in it's natural state. It will take on a patina that will darken with time, or
alternatively it can be dyed at this stage, but it's advisable to take the knife out before doing so.
Whatever you decide to do, the knife should only be left in the damp sheath for a couple of hours, then take it out carefully and if you can hang it in a warm place to harden.

These instructions will be included with your kit

More...

Fits blades 90mm.x 27mm Bushman

3.75mm Veg Tanned Leather: Soak for ten minutes in warm water and sew it up.

Dye with any colour, wrap your knife in cling film, work into sheath and leave for two hours, remove and allow to cure.

Use some Aussie Wax to finish it off.

More...

FOR WESTERN STYLE SHEATHS ONLY

1. First buy your sheath of leather from us

2. Email an outline or picture of your knife along with the length of the blade and thickness of your handle.

3. Specify if you want stitch marks.

Please allow 5 working days for this service